Vehicles
62 not categorized PORSCHE 996 REAR RUBBERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection 91133300902 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more) View/Change Diagram
$363.00
Make a selection 911561005003AV This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion; increased fade resistance and the tighter woven layers. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. Sold individually. 1 necessary per car. For m...(choose a part on the right to read more) View/Change Diagram
From $1,410.20
Make a selection 911561053003EQ Rear window cabrio top section, manufactured in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers for the mechanically operated tops. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. Sold individually. 1 necessary per car.
$984.50
Make a selection 91450302310S Just in from being reproduced, we finally have the front and rear bumper top seals available to all who need them. these have been discontinued for some time, and 40 year old rubber being what it is, they could all surely stand to be replaced. get a set now and save! General Fitment914 1970-76
$584.10
Make a selection 911561005006HA This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion; increased fade resistance and the tighter woven layers. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. Sold individually. 1 necessary per car. For m...(choose a part on the right to read more) View/Change Diagram
$1,633.50
Make a selection 91453187310 This nifty item squeezes the water from the side of the window glass and also prevents water from entering the door cavity. easily inchwormed into the gutter using silicone grease order a rear window cap to finish the job. View/Change Diagram
From $6.89
Make a selection 477411313B Rear; stock rubber (2 required per car) for 18 mm bar bushing id 15.70mm View/Change Diagram
From $8.12
Make a selection 95534124204
View/Change Diagram
From $10.00
Make a selection 96433307401S We specify that the manufacturer use a 25% more stiff grade of rubber known in the industry as 85 shore. 85 shore refers to the rubbers density or hardness value. Oem is 65 shore and the factory European rs models use 85 shore; it suffers from less deflection, maintains more precise alignment and gives you the same repetitive feeling corner after corner. With aircooled 911's going up so much in value these days, we wanted to create suspension parts that look 100% oem, but also offer sportier handling without being too stiff for street use. They are manufactured in europe by an OEM supplier using the finest materials available (high carbon steel, 7075 t6 aluminum and 85 shore rubber). Upgrade yours today! Sold ...(choose a part on the right to read more) General Fitment911 1989-94
$159.50
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 964561005016HA This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames, like the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German ...(choose a part on the right to read more)
$2,201.10
Make a selection FVD160993002 The length of this rear wiper specifically fits the 993 targa. Bosch micro edge excel wiper blades clean windshields better and last longer than ever before. This ultra performance wiper blade features an exclusive dual rubber compound with a fully-enclosed metal tension spring, housed in an aerodynamic steel frame. The result is less streaking and unmatched resistance to wear from weather and corrosive elements. And with the exclusive Bosch directconnectâ„¢ one-step system, installation is quick and easy. Sold individually. 1 necessary per car.
$20.90
Make a selection AA500A Our rubber kits are for the perfect restoration. Available only from Automobile Atlanta, this kit consists of everything we use in our restoration shop. General Fitment914 1970-76
$1,012.23
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection AP9972TT110 Continuing on our modification path for the Porsche 997.2 turbo, agency power has just finished and released their new carbon fiber cold air intake kit. the carbon fiber airbox is a direct replacement for the OEM intake box. the airbox is made using a prepreg process which allows the entire airbox to be flawless from pulls. similar in shape to the OEM box for fitment, this carbon fiber unit features enlarged holes to fit dual K&N cone air filters. the 2x2 weave is finished in a gloss clear coat and sits nicely where the standard plastic box once was. These filters are pressed in through the rear of the intake box utilizing the rubber seal on the filter as a secure fit. General Fitment911 2005-08
$1,500.95
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection 96433307301S We specify that the manufacturer use a 25% more stiff grade of rubber known in the industry as 85 shore. 85 shore refers to the rubbers density or hardness value. Oem is 65 shore and the factory European rs models use 85 shore; it suffers from less deflection, maintains more precise alignment and gives you the same repetitive feeling corner after corner. With aircooled 911's going up so much in value these days, we wanted to create suspension parts that look 100% oem, but also offer sportier handling without being too stiff for street use. They are manufactured in europe by an OEM supplier using the finest materials available (high carbon steel, 7075 t6 aluminum and 85 shore rubber). Upgrade yours today! Sold ...(choose a part on the right to read more) General Fitment911 1989-94
$159.50
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$429.00
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD33300909ATK This non-adjustable rear spring plate is remanufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car. This part is a remanufactured part. Send us your original and we will have it remanufactured for you. We do not offer a core exchange on this part. Each is remanufactured in Germany, so the lead times can vary.
$342.10
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD3439641PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,245.20
Make a selection ST91102 It is always a hassle to get into the rear of classic cars with their stationary seats, therefore GTS classics developed a tilting bracket that fits all of our seats and is a bolt in solution for the 911 and 912 until ‘73, and can be adapted for most other cars. We placed the lever in the middle so there would not be a difference between the right and left tilting brackets as well as giving the seat the ability to be released from either side. Three hinges and rubber stoppers were used to minimize movement and noise of the tilting bracket. Please contact us so we can assist you in finding the right seat, application and mountings for your project. This bracket fits all of the styles of GTS seats and is made e...(choose a part on the right to read more) General Fitment912 1965-69911 1965-69 911 1970-73
$306.00
Make a selection MIT1410 Our front and rear stock fiberglass bumpers incorporate both the face bar and rubber top seal into one piece, facilitating installation and saving hundreds over the originals. please keep in mind that fiberglass does not provide the crash protection of steel, but saves weight for autocross and track events! General Fitment914 1970-76
$460.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |